Electronic Bench Organizer

  This is an organizer especially designed for an electronic bench to hold small parts, screws, etc. Support is not needed. This object was designed using Solid Edge Community Edition.

Read More

Magazine File

  This a magazine file 60 mm wide. It is designed for letter size paper. It is by design a bit smaller than the document it holds. It has holes

Read More

CR-10 Under Bed Tray

  These are trays to put under a CR-10 3D printer. The separator of one tray are 15 mm in height. For the other one, 38 mm in height which

Read More

Hanging Open Box

  This is an open box that can be hanged using 2 screws. The diameter of the head of the screw must be less than 1 cm. Its dimensions are

Read More

3D Printing Trashcan

  This is a small trashcan for 3D printing. The way the cover is designed, plastic stuff in the trashcan won’t spring back outside it. The trashcan is 80 mm

Read More

Issues with Ubuntu 20.04 on AMD Ryzen 7 4800H and GeForce GTX 1660 Ti

UPDATE: Ubuntu 20.10 fixes the issues listed below. ASUS came out recently with very powerful gaming laptops at a very good price. The hardware is quite recent. Installing Linux on

Read More

Parametric Round Container

  It is a simple parametric round container. Open the ParametricBox.scad file with openScad ( http://www.openscad.org/ ) Modify the variables in Parameters.scad to suit your needs and save it. Open

Read More

Wires And Probes Hanger

  This object will let you suspend your wires and probes on a door. To complete this assembly, you will need a pipe or tube of 5/8 in or 16

Read More

Drawer Dividers for Small Parts Cabinet

  These are small drawer dividers. There are 2 models. One for the drawer cabinet sold by Canadian Tire. The other one is for drawer cabinet sold by Home Depot.

Read More

20mm Extrusion Vibration Absorber

  This is an anti-vibration foot for 20mm aluminum extrusion. I had good results using semi-flexible filament. I added some anti-sliding pad. They were specifically designed for an Ender-3 printer.

Read More

Kotto Fume Extractor Stand

  This is a stand for the Kotto Fume extractor that can be bought from Amazon. It raises the fume extractor by 3 cm. It can be printed without support.

Read More

Prusa MK3 Spool Holder with Bearings

  This is a spool holder designed for the Prusa MK3S or any Prusa i3 printers. The dimensions of the top of the main plate shoud be 6.25mm x 40mm.

Read More

2.36mm Wire Holder

  This is a small wire holder. It is designed for 2.36 mm wires in diameter including its insulation. It can be printed without support if printed on its side.

Read More

Mini Solder Spool

  Soldering electronic components using a large solder spool of 454 grams or so is quite inconvenient even if it is mounted on a solder spool holder. I prefer to

Read More

Pull Handle

  This is a simple pull handle. A #10 flat head screw is recommended to fasten it. I suggest using at least 30% infill. Support is not needed. This object

Read More

TRENDnet TK-409K KVM Holder for Ikea Ivar

  This is a holder for a TRENDnet TK-409K KVM. The holder is hanged on a unit side of the Ikea Ivar shelving system. The TRENDnet TK-409K is a 4

Read More

Parametric Bumper Feet

  This is a simple OpenSCAD project that generates bumper feet for various objects. It was specifically designed to replace the lost bumper feet of a Falcon Print Trimmer. Printing

Read More

Nuvistor Display Stand

  This is a display stand for an old electronic part: the Nuvistor which is a type of vacuum tube. It was announced by RCA in 1959. Support is not

Read More

ESP8266 Motion Sensor Case

  This is a case for a motion sensor based on the ESP8266 and the HC-SR501, a PIR (motion) sensor. Support is not required. This object was designed using Fusion

Read More

4 inches x 0.7 inches Label Holder

  This is a paper tag holder made out of 4 inches (10.1 cm) x 3 inches (7.6 cm) index cards. They fit an edge of about 1/4 (6.25 mm)

Read More