Another Pen Holder

This is a pen holder of an unusual design. Three sizes are available. You can increase the capacity of them by gluing another one on its side. Support is not

Read More

Waveshare Pi Pico Dual Expander Base Plate

This is a baseplate for the Waveshare Pi Pico Dual Expander. You will need 4 tiny screws to mount it. An infill of 15% is recommended. Support is not needed.

Read More

1802 Membership Card Stand

This is a simple stand for the 1802 (COSMAC ELF) Membership Card. The 1802 is a vintage micro-processor. You can get this kit at http://www.sunrise-ev.com/1802.htm . I’m not affiliated with

Read More

LG 27EA33 Storage Trays

This is a tray designed to be installed on the stand of an LG 27EA33 monitor. You need to print the STL file provided and the same file mirrored. You

Read More

Panavise 303 replacement pads

These are replacement pads for the Panavise 303 vise. It has groves to hold tubular objects. I’ve printed it in semi-flexible filament, but works fine printed in PLA. Support is

Read More

SBC Server Case

This is a modular SBC or Development Board enclosure. Its base design principle is you stack on top of each other plates that hold various devices such as Raspberry PI,

Read More

3.5 inch Hard Drive Box

This is a box for a 3.5 inch hard drive and its cover. It was specifically designed to fit in a small safety box often rented by banks. Support is

Read More

Electronic Bench Organizer

This is an organizer especially designed for an electronic bench to hold small parts, screws, etc. Support is not needed. This object was designed using Solid Edge Community Edition. Printable

Read More

Magazine File

This is a magazine file 60 mm wide. It is designed for letter size paper. It is by design a bit smaller than the document it holds. It has holes

Read More

CR-10 Under Bed Tray

These are trays to put under a CR-10 3D printer. The separator of one tray are 15 mm in height. For the other one, 38 mm in height which is

Read More

Hanging Open Box

  This is an open box that can be hanged using 2 screws. The diameter of the head of the screw must be less than 1 cm. Its dimensions are

Read More

3D Printing Trashcan

  This is a small trashcan for 3D printing. The way the cover is designed, plastic stuff in the trashcan won’t spring back outside it. The trashcan is 80 mm

Read More

Parametric Round Container

  It is a simple parametric round container. Open the ParametricBox.scad file with openScad ( http://www.openscad.org/ ) Modify the variables in Parameters.scad to suit your needs and save it. Open

Read More

Wires And Probes Hanger

  This object will let you suspend your wires and probes on a door. To complete this assembly, you will need a pipe or tube of 5/8 in or 16

Read More

Drawer Dividers for Small Parts Cabinet

  These are small drawer dividers. There are 2 models. One for the drawer cabinet sold by Canadian Tire. The other one is for drawer cabinet sold by Home Depot.

Read More

40 mm Extrusion Vibration Absorber

This is an anti-vibration foot for 40 mm aluminum extrusion. I had good results using semi-flexible filament. I added some anti-sliding pad. They were specifically designed for an Ender-3 printer.

Read More

Kotto Fume Extractor Stand

  This is a stand for the Kotto Fume extractor that can be bought from Amazon. It raises the fume extractor by 3 cm. It can be printed without support.

Read More

Prusa MK3 Spool Holder with Bearings

  This is a spool holder designed for the Prusa MK3S or any Prusa i3 printers. The dimensions of the top of the main plate shoud be 6.25mm x 40mm.

Read More

2.36mm Wire Holder

  This is a small wire holder. It is designed for 2.36 mm wires in diameter including its insulation. It can be printed without support if printed on its side.

Read More

Mini Solder Spool

  Soldering electronic components using a large solder spool of 454 grams or so is quite inconvenient even if it is mounted on a solder spool holder. I prefer to

Read More