ctheroux.com

Ikea Skogsta Bins

May 27, 2018 · admin 3D Printing object

These are small bins for the Ikea Skogsta tool box. Three styles are provided: for both corners and between the corner bins. They are 60 x 80 mm. The middle ones are 60 x 70 mm.

This is a case to a 15W audio amplifier board that can be found on eBay, AliExpress, ... such as https://www.aliexpress.com/store/product/Hot-Sale-1pc-TDA7297-Version-B-2-15W-Digital-For-Audio-Amplifier-Board-Dual-Channel-AC/1959068\_32666077241.html?spm=2114.12010615.0.0.7a894502EdjFEn . I use this amplifier for an Asus Tinker Board.

Sink Bucket with drainage holes

April 15, 2018 · admin 3D Printing object

This is a bucket having many drainage holes on all sides. It can be hung using the optional holder who must be separately printed and attached. It can be done using hot glue.

Tactical Strike Ammunition Reservoir Extension

January 28, 2018 · admin 3D Printing object

This is an ammunition magazine extension for the Tactical Strike (Adventure Force). It is like a Nerf gun except that the ammunition is balls.

Fume Extractor V2

December 27, 2017 · admin 3D Printing object

This fume extractor uses carbon filters of 130mm x 130mm x 10mm. These are used for the HAKKO 491/493 fume extractor. To build it, you'll need:

Power Supply Mounting Brackets

December 3, 2017 · admin 3D Printing object

These are "Mean Well" type power supply mounting brackets. You will be able to mount this type of power supply on a surface using screws. This bracket is quite sturdy. The slot on the bracket that holds the power supply supports up to M4 screws. It is recommended that you use washers. The hole used to screw the power supply to the surface are 5 mm in diameter.

Dual 16850 Battery Holder Mounting Plate

November 5, 2017 · admin 3D Printing object

This is a mounting plate for a Dual 16850 Battery Holder. It allows to screw the battery holder to a surface without having to put screws inside the battery holder. It prevents damages to the battery that could be made by using inner screws. The holes for the screws are 90 mm apart. The plate is 40 mm x 75 mm. The screw holes are 3.25 mm in diameter. The plate is 1 mm thick.

FlySky FS-iA6B Receiver Holder

October 30, 2017 · admin 3D Printing object

This is a simple holder for a FS-iA6B Radio Receiver. The holder is 49 mm wide, 12 mm in height and 10 mm deep. The mounting holes are 39 mm apart and uses M3 or #4 screws.

CR-10 X-axis Height Adjustment Tool

October 30, 2017 · admin 3D Printing object

This is a X axis height adjustment tool designed for the CR-10, especially if the Z axis upgrade is installed. Nevertheless, it can be certainly used for other 3D printers. You need to print two tools to use it.

Mini and Half Breadboard Mounting Plates

October 29, 2017 · admin 3D Printing object

These are mounting plates for the mini and half size breadboards. Sometimes, I use a breadboard temporarily for a project. It is messy to remove it if it was sticked to a component of the project using the double sided tape underneath it. Also, it is difficult to re-use it. So, I have design these mounting plates. I stick the breadboard on a mounting plate and use the holes to mount it on the project. It is then easy to remove and re-use it in another project. The mounting holes are 48 mm apart for the mini breadboards and 67 mm for the half size breadboards.

Ikea Skogsta Bins

15W Stereo Amplifier Case

Sink Bucket with drainage holes

Tactical Strike Ammunition Reservoir Extension

Fume Extractor V2

Power Supply Mounting Brackets

Dual 16850 Battery Holder Mounting Plate

FlySky FS-iA6B Receiver Holder

CR-10 X-axis Height Adjustment Tool

Mini and Half Breadboard Mounting Plates

Tags