ctheroux.com

Mini and Half Breadboard Mounting Plates

October 29, 2017 · admin 3D Printing object

These are mounting plates for the mini and half size breadboards. Sometimes, I use a breadboard temporarily for a project. It is messy to remove it if it was sticked to a component of the project using the double sided tape underneath it. Also, it is difficult to re-use it. So, I have design these mounting plates. I stick the breadboard on a mounting plate and use the holes to mount it on the project. It is then easy to remove and re-use it in another project. The mounting holes are 48 mm apart for the mini breadboards and 67 mm for the half size breadboards.

Classic Arduino Mouning Plate

October 22, 2017 · admin 3D Printing object

This is a mounting plate for the classic Arduino's Duemilanove/Diecimila/NG/Uno and any other ones that has the same form factor. This mounting plate serves three purposes:

L298D Motor Driver Mouning Plate

October 22, 2017 · admin 3D Printing object

This is a mounting plate for the dual motors driver board that uses a L298D. They are widely available. This mounting plate serves three purposes:

CR-10 X-Axis Led Strip Holder

October 15, 2017 · admin 3D Printing object

This is a led strip holder that latches in the X axis extrusion slot of a CR-10 3D printer. You attach a led strip to the bottom to light up the bed while printing an object. This is a remix of http://www.thingiverse.com/thing:2252158. I removed the bottom grove. It can be now used with wider led strips and printing support is no longer required. Also, I increased its length to 24 cm and this version is wider: 22 mm. I have added two holes to hold the the wires with zip ties.

Logitech C170 Privacy Shield

October 10, 2017 · admin 3D Printing object

This is a privacy shield that you put on your Logitech C170 webcam in order to block the lens and thus to ensure your privacy.

Sturdy Cable Holder

October 9, 2017 · admin 3D Printing object

This is a simple robust cable holder. Why robust? The other ones I designed were too weak. With time, they were bending from the weight of the cables. With 8 slots, its overall size is about 15 cm (W) x 4 cm (D) x 2.5 cm (H) or 6" (W) x 1"1/2 (D) x 1" (H).

Wall Mounted Pen Cup

July 30, 2017 · admin 3D Printing object

This is a simple pen cup that can be mounted to a wall. It is divided into three compartments of equal sizes. Its size is about 14 cm (W) x 6 cm (D) x 87 cm (H). The distance between the mounting holes is 10 cm.

Suspended Glass For Photography - 1-1/4 Inch Pipe Foot

May 15, 2017 · admin 3D Printing object

This model can be used for many purposes. Nevertheless, it was mainly designed to suspend a sheet of glass in the air. This setup is used to take pictures of small objects without shadows. This object is designed for standard 1-1/4 inch abs drain pipe. You will need the following to make the photo suspended glass. - 4 x 1-1/4-inch drain pipe. Mines are 9 inches in length. - 4 feet. - 2 somewhat rigid rods. I have used steel rods, 3/16 inch in diameter. - 1 thin sheet of glass. - 1 large piece of paper or thin cardboard. Drill holes near the top of the pipes to insert the rods.

Rigid 18V Vacuum Nozzle

May 15, 2017 · admin 3D Printing object

This is a simple wide nozzle for a Rigid Gen5X Brushless 18V Wet/Dry Vacuum. The internal diameter is about 31.5 mm or 1-1/4 inch.

How to install Pronterface on Ubuntu 16.04

April 30, 2017 · admin Ubuntu 3D Printing

To install Pronterface on Unbuntu, first install the dependencies.

Tags