ctheroux.com

Classic Arduino Mouning Plate

October 22, 2017 · admin 3D Printing object

This is a mounting plate for the classic Arduino's Duemilanove/Diecimila/NG/Uno and any other ones that has the same form factor. This mounting plate serves three purposes:

L298D Motor Driver Mouning Plate

October 22, 2017 · admin 3D Printing object

This is a mounting plate for the dual motors driver board that uses a L298D. They are widely available. This mounting plate serves three purposes:

CR-10 X-Axis Led Strip Holder

October 15, 2017 · admin 3D Printing object

This is a led strip holder that latches in the X axis extrusion slot of a CR-10 3D printer. You attach a led strip to the bottom to light up the bed while printing an object. This is a remix of http://www.thingiverse.com/thing:2252158. I removed the bottom grove. It can be now used with wider led strips and printing support is no longer required. Also, I increased its length to 24 cm and this version is wider: 22 mm. I have added two holes to hold the the wires with zip ties.

Logitech C170 Privacy Shield

October 10, 2017 · admin 3D Printing object

This is a privacy shield that you put on your Logitech C170 webcam in order to block the lens and thus to ensure your privacy.

Sturdy Cable Holder

October 9, 2017 · admin 3D Printing object

This is a simple robust cable holder. Why robust? The other ones I designed were too weak. With time, they were bending from the weight of the cables. With 8 slots, its overall size is about 15 cm (W) x 4 cm (D) x 2.5 cm (H) or 6" (W) x 1"1/2 (D) x 1" (H).

Wall Mounted Pen Cup

July 30, 2017 · admin 3D Printing object

This is a simple pen cup that can be mounted to a wall. It is divided into three compartments of equal sizes. Its size is about 14 cm (W) x 6 cm (D) x 87 cm (H). The distance between the mounting holes is 10 cm.

Suspended Glass For Photography - 1-1/4 Inch Pipe Foot

May 15, 2017 · admin 3D Printing object

This model can be used for many purposes. Nevertheless, it was mainly designed to suspend a sheet of glass in the air. This setup is used to take pictures of small objects without shadows. This object is designed for standard 1-1/4 inch abs drain pipe. You will need the following to make the photo suspended glass. - 4 x 1-1/4-inch drain pipe. Mines are 9 inches in length. - 4 feet. - 2 somewhat rigid rods. I have used steel rods, 3/16 inch in diameter. - 1 thin sheet of glass. - 1 large piece of paper or thin cardboard. Drill holes near the top of the pipes to insert the rods.

Rigid 18V Vacuum Nozzle

May 15, 2017 · admin 3D Printing object

This is a simple wide nozzle for a Rigid Gen5X Brushless 18V Wet/Dry Vacuum. The internal diameter is about 31.5 mm or 1-1/4 inch.

Case for the GM328A Components Tester

March 7, 2017 · admin 3D Printing object

This object is a case for the GM328A Electronic Components Tester. It has a compartment for the 9V battery and an access hole for the extra test leads. The thin plate on the battery cover should be placed between the Component Tester and the battery to prevent any short circuits. 6 screws such as M3 x 12mm are required. Similar screws will also fit.

Prusa i3 Simple LCD Holder

March 6, 2017 · admin 3D Printing object

This is a simple Reprap character based LCD holder for a Prusa i3 3D printer. It is designed to be attached to a 6.35 mm tick frame, 45 mm in length. To mount this holder on the frame, you will need: - 1 x M3 25 mm screw with its nut - 1 x M3 16 mm screw with its nut. The LCD is mounted using six screws. The screws shall be small. Pilot holes are provided. A drill bit is needed to enlarge the pilot holes to fit the screws you will be using to mount the LCD on the holder. The holder is slightly tilted downward. The holder can be easily modified with a file to make it tilt upward.

Tags