Category: 3D Printing
Wera Micro Screwdriver Stackable Tray
This is a tray that holds up to 8 Wera micro screwdrivers. The design will hold the screwdriver labels upright. Multiple trays may be stacked. Support material is required for
Read MoreMicro SD Card Carrier
This object is a simple micro SD card carrier having the same size as an SD card. It was designed to put a micro SD card into a SD card
Read MoreRaspberry PI Case 1B+/2/3
This is a minimalist case for a Raspberry Pi 1B+, 2 or 3. Why another case when there are so many out there? This one has the smallest footprint. Most
Read MoreDIN Rail Prototyping Stand V02
This is a stand when used with some DIN Rails makes a useful electronic prototyping rig. You will be able to move your prototypes easily with it. Feet are also
Read MoreWaveshare Pi Pico Quad Expander Base Plate
This is a baseplate for the Waveshare Pi Pico Quad Expander. You will need 4 or more tiny screws to mount it. An infill of 15% is recommended. Support is
Read MoreCoaster Set
This is a coaster set. This design limits the contact surface between the recipient and the coaster. The deep design prevents the condensation waters from touching the recipient. Two storage
Read MoreTronXY X5SA Z Cable Chain Holder
This is a replacement of the stock Z Axis Cable Chain Holder of the TronXY X5SA. The straight design is inappropriate because of the nuts on the extrusion side. I
Read MoreDIN Rail Prototyping Stand
This is a stand when used with some DIN Rails makes a useful electronic prototyping rig. You will be able to move your prototypes easily with it. In the picture,
Read More4 Digits Nixie Tube Clock Stand
This is a 15 mm in height stand for a 4 Digits Nixie Tube Clock. This clock is available on AliExpress. The base of the clock is 40 mm x
Read MoreAnother Pen Holder
This is a pen holder of an unusual design. Three sizes are available. You can increase the capacity of them by gluing another one on its side. Support is not
Read MoreWaveshare Pi Pico Dual Expander Base Plate
This is a baseplate for the Waveshare Pi Pico Dual Expander. You will need 4 tiny screws to mount it. An infill of 15% is recommended. Support is not needed.
Read More1802 Membership Card Stand
This is a simple stand for the 1802 (COSMAC ELF) Membership Card. The 1802 is a vintage micro-processor. You can get this kit at http://www.sunrise-ev.com/1802.htm . I’m not affiliated with
Read MoreLG 27EA33 Storage Trays
This is a tray designed to be installed on the stand of an LG 27EA33 monitor. You need to print the STL file provided and the same file mirrored. You
Read MorePanavise 303 replacement pads
These are replacement pads for the Panavise 303 vise. It has groves to hold tubular objects. I’ve printed it in semi-flexible filament, but works fine printed in PLA. Support is
Read MoreSBC Server Case
This is a modular SBC or Development Board enclosure. Its base design principle is you stack on top of each other plates that hold various devices such as Raspberry PI,
Read More3.5 inch Hard Drive Box
This is a box for a 3.5 inch hard drive and its cover. It was specifically designed to fit in a small safety box often rented by banks. Support is
Read MoreElectronic Bench Organizer
This is an organizer especially designed for an electronic bench to hold small parts, screws, etc. Support is not needed. This object was designed using Solid Edge Community Edition. Printable
Read MoreMagazine File
This is a magazine file 60 mm wide. It is designed for letter size paper. It is by design a bit smaller than the document it holds. It has holes
Read MoreCR-10 Under Bed Tray
These are trays to put under a CR-10 3D printer. The separator of one tray are 15 mm in height. For the other one, 38 mm in height which is
Read MoreHanging Open Box
This is an open box that can be hanged using 2 screws. The diameter of the head of the screw must be less than 1 cm. Its dimensions are
Read More