ASUS VA32A Monitor Storage Add-On set 3

These are some add-ons for the ASUS VA32A Monitor Storage. It includes pen and pencil trays. The ASUS VA32A Monitor Storage project is located at http://www.ctheroux.com/asus-va32a-monitor-tray-system/ . Print them at

Read More

Parametric Macro Pad

This is a parametric macro pad using a Pi Pico. It uses Cherry MX compatible switches. You’ll need a few drops of glue to mount the switches plate on the

Read More

Parametric Vesa Monitor Extension

This is a parametric Vesa Monitor extension. Be careful of the length of it since it’s made of plastic. It may either break or you mounting device will break. Use

Read More

Parametric Washer

This is a simple parametric washer. Support material is not required. An infill of 30% is recommended. This object was designed using openSCAD. Printable Files    Sample washer    Parametric

Read More

Filament Bag Electric Air Pump Case

This is a case for a filament bag electric air pump widely available. Support material is not required. An infill of 20% is recommended. This object was designed using openSCAD.

Read More

Utensil Dripper – Dryer

This is a utensil dripper/dryer, mainly used to air dry utensils. A riser is provided. It let any water that went underneath the dripper dry. A few drops of glue

Read More

Make nvim-tree width dynamic

Create a file named ~/.config/nvim/lua/plugins/nvim-tree.lua and put the following content:

Read More

How to merge two git repositories

These steps will let you merge a source repository into a destination repository.

Read More

Ikea Ivar Pole Cylinders

These objects are a pair of slanted cylinders that are installed on a post of an Ikea Ivar shelving unit. They can be used to hold flashlights, cans, and so

Read More

Parametric Watering Can

Parametric Watering Can ——————————————————————————– This is a parametric watering can. Support material may not be required depending on your parameters. An infill of 100% is recommended. This object was designed

Read More

Parametric Wire Tube Holder and Wire Cap

These are a parametric wire tube holder along with a parametric wire cap for already installed wires. A single screw is needed to install one tube holder. Support material is

Read More

Case for a UT353 Sound Meter

This is a case for a Uni-T UT353 Sound Meter. It is designed that the foam doesn’t touch any surface to prevent deformation. A drop of glue is required to

Read More

How to fork a project from your repository

These commands let you fork a project hosted on your own git repository.

Read More

nvim-tree variable width

In order for nvim-tree to adapt its width to its content, create a file named ~/.config/nvim/lua/plugins/nvim-tree.lua. Put the following content into it.

Read More

Paper Tissue Box Cover

This is a paper tissue box cover. Its internal size is 11.4 cm x 22.0 cm x 8.3 cm. Support material is not required. An infill of 20% is recommended.

Read More

Parametric Label Holder

This is a Parametric Label Holder that can be glued on drawers and so on. The size of the labels is given in the openSCAD log. Support material is not

Read More

32 x 8 Led Matrix Case with MCU

This is a case for a 32 x 8 LED matrix and an ESP8266 MCU. It runs on 5V (USB). I’ve made a connected clock with it.  Its purpose is

Read More

Harley-Davidson Logo

This object is two Harley-Davidson logos, 40 mm and 60 mm, I’ve made for an HD motorcycle fanatic. Support material is not required. An infill of 20% is recommended. This

Read More

Box for an Electronic Load

Box for an Electronic Load ——————————————————————————– This is a box for the commonly available Electronic Load on AliExpress. You’ll need a drop to glue the cover latch (the very tiny

Read More

Install NeoVim along with NVChad installation

NeoVim has a tremendous number of improvements compared to Vi. As with Vi, it has a very steep ram-up. Basically, you have to configure from zero, which is not easy

Read More