Parametric Washer

This is a simple parametric washer. Support material is not required. An infill of 30% is recommended. This object was designed using openSCAD. Printable Files    Sample washer    Parametric

Read More

Filament Bag Electric Air Pump Case

This is a case for a filament bag electric air pump widely available. Support material is not required. An infill of 20% is recommended. This object was designed using openSCAD.

Read More

Utensil Dripper – Dryer

This is a utensil dripper/dryer, mainly used to air dry utensils. A riser is provided. It let any water that went underneath the dripper dry. A few drops of glue

Read More

Ikea Ivar Pole Cylinders

These objects are a pair of slanted cylinders that are installed on a post of an Ikea Ivar shelving unit. They can be used to hold flashlights, cans, and so

Read More

Parametric Watering Can

Parametric Watering Can ——————————————————————————– This is a parametric watering can. Support material may not be required depending on your parameters. An infill of 100% is recommended. This object was designed

Read More

Parametric Wire Tube Holder and Wire Cap

These are a parametric wire tube holder along with a parametric wire cap for already installed wires. A single screw is needed to install one tube holder. Support material is

Read More

Case for a UT353 Sound Meter

This is a case for a Uni-T UT353 Sound Meter. It is designed that the foam doesn’t touch any surface to prevent deformation. A drop of glue is required to

Read More

Paper Tissue Box Cover

This is a paper tissue box cover. Its internal size is 11.4 cm x 22.0 cm x 8.3 cm. Support material is not required. An infill of 20% is recommended.

Read More

Parametric Label Holder

This is a Parametric Label Holder that can be glued on drawers and so on. The size of the labels is given in the openSCAD log. Support material is not

Read More

32 x 8 Led Matrix Case with MCU

This is a case for a 32 x 8 LED matrix and an ESP8266 MCU. It runs on 5V (USB). I’ve made a connected clock with it.  Its purpose is

Read More

Harley-Davidson Logo

This object is two Harley-Davidson logos, 40 mm and 60 mm, I’ve made for an HD motorcycle fanatic. Support material is not required. An infill of 20% is recommended. This

Read More

Box for an Electronic Load

Box for an Electronic Load ——————————————————————————– This is a box for the commonly available Electronic Load on AliExpress. You’ll need a drop to glue the cover latch (the very tiny

Read More

Wiha Bit Holder for Skadis Pegboard

This is a twin Wiha bit holder for Ikea Skadis pegboard. It holds 2 Wiha 7 bits case. A few drops of CA glue is required to glue the pegboard

Read More

4 Liters Airtight Container Hygrometer Holder

This object holds a square hygrometer in a 4 liters airtight container. This object was designed to monitor the 3D printing filament moisture. I’ve used a small piece of Velcro

Read More

Ikea Skadis Large Dewalt Organizer Hook

This is a hook to hang a large Dewalt organizer. Support material that touches the build plate is required. An infill of 20% is recommended. A 100% infill is recommended

Read More

Ikea Vattenkar To-do List Holder

This to-do list holder is designed to be installed on a Vattenkar desk organizer from Ikea. It uses 3 x 5 inches index card. A template is provided to draw

Read More

Parametric Can Stacking Spacers

These spacers let you stack can of food easily. You can customize them using openSCAD. Take a copy of CanStackingDisks_Parameters.scad and update the parameters. Open the file with openSCAD and

Read More

Skadis mounting bracket for Nissafors utility cart.

Skadis mounting bracket for Nissafors utility cart. ——————————————————————————– This is a mounting bracket to attach a Skadis pegboard to a Nissafors utility cart. You’ll need 4 pieces of each object.

Read More

Kingston Hyper X Alloy FPS Pro Riser

This is a keyboard riser for the Kingston Hyper X Alloy FPS Pro, mini USB edition. Support material is not required. An infill of 20% is recommended. This object was

Read More

4 Litres Airtight Container Filament Name Cardholder

This is a device that holds cards that identify the filament stored in a 4 litres airtight container. This design is slightly curved to fit the end of the container.

Read More