Category: object
FLSun Cube X-Axis Belt Tensioner
The FLSun Cube 3D printer does not come with an X-Axis belt tensioner. So, I designed one. The design is simple but very effective. It is mounted using the
Read MoreFLSun Cube Bed Level Adjustment Tool
This is a simple tool to adjust the level of the bed of a FLSun Cube. Likely, it can be used with other printers such as the CR-10. Print
Read MoreFLSun Cube Bed Cable Strain Relief
This is a strain relief for the heated bed cables of the FLSun Cube. A zip tie is used to fix it to the bed frame. I drilled a
Read MoreFLSun Cube Extruder Cable Strain Relief/Holder i2
This is a strain relief for the wires and the PTFE tube attached to the extruder of the FLSun Cube 3D printer. It is installed using the bolts of
Read More2020 Extrusion Power Supply Stabilizer
This is a simple stabilizer for a power supply designed to be attached to a 2020 aluminum extrusion. This stabilizer is designed for the FLSun Cube. You will need
Read MoreFLSun Cube Extruder Cable Strain Relief/Holder
This is a strain relief for the wires and the PTFE tube attached to the extruder of the FLSun Cube 3D printer. It is installed using the bolts of
Read More20 mm wide 135 Degrees T-Slot Angle Brackets
20 x 20 x 20 mm, 20 x 40 x 40 mm and 20 x 60 x 60 mm 135 degrees T-Slot brackets. For 90 degrees versions of these
Read MoreEditing Extra large 20×4 LCD Project Box
This is a project box for a large 20 x 4 LCD display. The LCD module dimensions are 146mm x 62.5mm x 20mm (5.75 inches x 2.46 inches x
Read MorePrusa i3 X-Axis Leveling Tool
This is a simple tool that will help you level the X-axis of a Prusa i3. You will need to print two of this. You can use them either
Read MoreJetson Nano Base with Camera
This is a simple base plate for the NVidia Jetson Nano development board along with a Raspberry PI v2.1 camera holder. It can be tilted and panned. To assemble
Read MoreEPM240 CPLD Development Board Base Plate
This is a base plate for the Altera Max II EPM240 CPLD Development Board from LC Technologies. You will need 4 M2 x 4mm screws to assemble it. No
Read MoreJetson Nano Base Plate
This is a simple base plate for the NVidia Jetson Nano development board. 4 x #4-40, 1/4″ bolts are required to assemble it. No support is required. An infill
Read MoreParametric Bottle Rack
This is a simple SCAD file that generates bottle rack. Various sizes are included. To create a custom one: Open the ParametricBottleRack.scad file with openScad ( http://www.openscad.org/ ) Modify
Read MoreParametric Drink Coaster
This is a simple SCAD file that generates round coaster. Various sizes are included. To create a custom one: Open the ParametricCoaster.scad file with openScad ( http://www.openscad.org/ ) Modify
Read MoreIvar Cable Hanger
This is a cable hanger to be installed on the side unit of the Ivar shelving system. You will need 2 #4-40, 1/2″ bolts and the matching nuts. Support
Read MoreBusiness Card Holder
This is a simple business card holder that can be hang on a 5 mm wide support. It can hold about 50 cards. It should be printed upright with
Read MorePower Brick Holder
This is a holder for a power brick of 18 cm (7 inches) in length, 4.5 cm (1 3/4 inch) tick and typically 7 cm (2 3/4 inches) in
Read MoreP4.75-1R1G-16S Led Matrix Stand
This is a set of feet for the p4.75-1R1G-16S Led Matrix (32 x 64). It holds the display at a 30-degrees angle. You will need two 8mm M3 screws
Read MoreRecycling Bin Holder
This is a Recycling Bin Holder 220 mm long. It is held by two screws. No support is needed. This object was designed using Fusion 360 Printable Files
Read MoreDFR-0499 Led Matrix Stand
This is a set of feet for the DFR-0499 RGB Led Matrix (64 x 64). It holds the display at a 30-degrees angle. You will need two 8mm M3
Read More