Fluval Flex 15 Gallons Light Replacement

This is a light replacement for a Fluval Flex 15 gallons aquarium. You will need a strip of WRBG LEDs. I suggest you to reuse the supplied LED controller. I’ve used some epoxy glue to seal the lens to the base and the wires to make it water tight. The lenses are best printed vertically. This light fixture is held using 2 thin holders using the 2 original screws. You will also need a soldering iron, some wires and shrink tubing to assemble the electronics to the LED strip.

Support material is not required. An infill of 20% is recommended.

This object was designed using Solid Edge Community Edition.


Printable Files

  Led Base
  Open side lens
  Close side lens
  Light holder

This object is also published on the following site(s):
Prusa Printers
Thingiverse


The source files are available:

You may request the source file(s) of this object. Ask for it by posting a comment below. Your email address will NOT be used for any other purposes than delivering you the source files. By doing so:

You are free to:

* Share — copy and redistribute the material except the source files in any medium or format
* Adapt — remix, transform, and build upon the material

You agree to:

* give appropriate credit, provide a link to the license, and indicate if changes were made. You may do so in any reasonable manner, but not in any way that suggests the licensor endorses you or your use.
* not use the material for commercial purposes
* distribute your contributions under the same license as the original if you remix, transform, or build upon the material
* not apply legal terms or technological measures that legally restrict others from doing anything the license permits.
* not upload the source files or modified source files on any sites. They are made available for your personal usage only. Nevertheless, you are allowed to upload the resulting STL or OBJ files.

If you do not agree to any of these conditions, do NOT request the source files.


Copyright 2012-2022 by Claude “Tryphon” Théroux

This is a light replacement for a Fluval Flex 15 gallons aquarium. You will need a strip of WRBG LEDs. I suggest you to reuse the supplied LED controller. I’ve used some epoxy glue to seal the lens to the base and the wires to make it water tight. The lenses are best printed vertically. This light fixture is held using 2 thin holders using the 2 original screws. You will also need a soldering iron, some wires and shrink tubing to assemble the electronics to the LED strip.

Support material is not required. An infill of 20% is recommended.

This object was designed using Solid Edge Community Edition.


Printable Files

  Led Base
  Open side lens
  Close side lens
  Light holder

This object is also published on the following site(s):
Prusa Printers
Thingiverse


The source files are available:

You may request the source file(s) of this object. Ask for it by posting a comment below. Your email address will NOT be used for any other purposes than delivering you the source files. By doing so:

You are free to:

* Share — copy and redistribute the material except the source files in any medium or format
* Adapt — remix, transform, and build upon the material

You agree to:

* give appropriate credit, provide a link to the license, and indicate if changes were made. You may do so in any reasonable manner, but not in any way that suggests the licensor endorses you or your use.
* not use the material for commercial purposes
* distribute your contributions under the same license as the original if you remix, transform, or build upon the material
* not apply legal terms or technological measures that legally restrict others from doing anything the license permits.
* not upload the source files or modified source files on any sites. They are made available for your personal usage only. Nevertheless, you are allowed to upload the resulting STL or OBJ files.

If you do not agree to any of these conditions, do NOT request the source files.


Copyright 2012-2022 by Claude “Tryphon” Théroux

Leave comment

Your email address will not be published. Required fields are marked with *.

Time limit is exhausted. Please reload the CAPTCHA.