Author: ctheroux
20 mm wide 135 Degrees T-Slot Angle Brackets
20 x 20 x 20 mm, 20 x 40 x 40 mm and 20 x 60 x 60 mm 135 degrees T-Slot brackets. For 90 degrees versions of these
Read MoreEditing Extra large 20×4 LCD Project Box
This is a project box for a large 20 x 4 LCD display. The LCD module dimensions are 146mm x 62.5mm x 20mm (5.75 inches x 2.46 inches x
Read MorePrusa i3 X-Axis Leveling Tool
This is a simple tool that will help you level the X-axis of a Prusa i3. You will need to print two of this. You can use them either
Read MoreJetson Nano Base with Camera
This is a simple base plate for the NVidia Jetson Nano development board along with a Raspberry PI v2.1 camera holder. It can be tilted and panned. To assemble
Read MoreEPM240 CPLD Development Board Base Plate
This is a base plate for the Altera Max II EPM240 CPLD Development Board from LC Technologies. You will need 4 M2 x 4mm screws to assemble it. No
Read MoreJetson Nano Base Plate
This is a simple base plate for the NVidia Jetson Nano development board. 4 x #4-40, 1/4″ bolts are required to assemble it. No support is required. An infill
Read MoreParametric Bottle Rack
This is a simple SCAD file that generates bottle rack. Various sizes are included. To create a custom one: Open the ParametricBottleRack.scad file with openScad ( http://www.openscad.org/ ) Modify
Read MoreParametric Drink Coaster
This is a simple SCAD file that generates round coaster. Various sizes are included. To create a custom one: Open the ParametricCoaster.scad file with openScad ( http://www.openscad.org/ ) Modify
Read MoreIvar Cable Hanger
This is a cable hanger to be installed on the side unit of the Ivar shelving system. You will need 2 #4-40, 1/2″ bolts and the matching nuts. Support
Read MoreBusiness Card Holder
This is a simple business card holder that can be hang on a 5 mm wide support. It can hold about 50 cards. It should be printed upright with
Read MorePower Brick Holder
This is a holder for a power brick of 18 cm (7 inches) in length, 4.5 cm (1 3/4 inch) tick and typically 7 cm (2 3/4 inches) in
Read MoreP4.75-1R1G-16S Led Matrix Stand
This is a set of feet for the p4.75-1R1G-16S Led Matrix (32 x 64). It holds the display at a 30-degrees angle. You will need two 8mm M3 screws
Read MoreRecycling Bin Holder
This is a Recycling Bin Holder 220 mm long. It is held by two screws. No support is needed. This object was designed using Fusion 360 Printable Files
Read MoreDFR-0499 Led Matrix Stand
This is a set of feet for the DFR-0499 RGB Led Matrix (64 x 64). It holds the display at a 30-degrees angle. You will need two 8mm M3
Read MoreParametric Storage Box
This is a simple SCAD file that generates a storage box and its cover. To create a box: Open the ParametricBox.scad file with openScad ( http://www.openscad.org/ ) Modify the
Read MoreFoam Board Screen
These are simple brackets used to build a screen from 5 mm foam board. Using the proper size of foam board, it can be used for airbrushing, etc. Print
Read MoreInsulated Screwdriver Rack
This is a compact rack for the Mastercraft Insulated Screwdrivers set (8 pieces) (#057-3695-4) No support is needed if printed on its side. This object was designed using Fusion
Read MoreInsulated Precision Screwdriver Rack
This is a compact rack for the Mastercraft Insulated Precision Screwdrivers set (6 pieces) (#057-3604-2) No support is needed if printed on its side. This object was designed using
Read MoreGolden Airbrush Paint (30 mm) Caddy
This is a caddy that can hold up to 18 Airbush Paint Bottles. The bottle can have a diameter of up to 30 mm. The design allows to print
Read MoreSingle Edge Razor Blade Rack
This is a simple rack that holds 4 single edge razor blades. Support is not needed. This object was designed using Fusion 360 Printable Files Single Edge Razor
Read More