Category: 3D Printing
Hanging Open Box
This is an open box that can be hanged using 2 screws. The diameter of the head of the screw must be less than 1 cm. Its dimensions are
Read More3D Printing Trashcan
This is a small trashcan for 3D printing. The way the cover is designed, plastic stuff in the trashcan won’t spring back outside it. The trashcan is 80 mm
Read MoreParametric Round Container
It is a simple parametric round container. Open the ParametricBox.scad file with openScad ( http://www.openscad.org/ ) Modify the variables in Parameters.scad to suit your needs and save it. Open
Read MoreWires And Probes Hanger
This object will let you suspend your wires and probes on a door. To complete this assembly, you will need a pipe or tube of 5/8 in or 16
Read MoreDrawer Dividers for Small Parts Cabinet
These are small drawer dividers. There are 2 models. One for the drawer cabinet sold by Canadian Tire. The other one is for drawer cabinet sold by Home Depot.
Read More40 mm Extrusion Vibration Absorber
This is an anti-vibration foot for 40 mm aluminum extrusion. I had good results using semi-flexible filament. I added some anti-sliding pad. They were specifically designed for an Ender-3 printer.
Read MoreKotto Fume Extractor Stand
This is a stand for the Kotto Fume extractor that can be bought from Amazon. It raises the fume extractor by 3 cm. It can be printed without support.
Read MorePrusa MK3 Spool Holder with Bearings
This is a spool holder designed for the Prusa MK3S or any Prusa i3 printers. The dimensions of the top of the main plate shoud be 6.25mm x 40mm.
Read More2.36mm Wire Holder
This is a small wire holder. It is designed for 2.36 mm wires in diameter including its insulation. It can be printed without support if printed on its side.
Read MoreMini Solder Spool
Soldering electronic components using a large solder spool of 454 grams or so is quite inconvenient even if it is mounted on a solder spool holder. I prefer to
Read MorePull Handle
This is a simple pull handle. A #10 flat head screw is recommended to fasten it. I suggest using at least 30% infill. Support is not needed. This object
Read MoreTRENDnet TK-409K KVM Holder for Ikea Ivar
This is a holder for a TRENDnet TK-409K KVM. The holder is hanged on a unit side of the Ikea Ivar shelving system. The TRENDnet TK-409K is a 4
Read MoreParametric Bumper Feet
This is a simple OpenSCAD project that generates bumper feet for various objects. It was specifically designed to replace the lost bumper feet of a Falcon Print Trimmer. Printing
Read MoreNuvistor Display Stand
This is a display stand for an old electronic part: the Nuvistor which is a type of vacuum tube. It was announced by RCA in 1959. Support is not
Read MoreESP8266 Motion Sensor Case
This is a case for a motion sensor based on the ESP8266 and the HC-SR501, a PIR (motion) sensor. Support is not required. This object was designed using Fusion
Read More4 inches x 0.7 inches Label Holder
This is a paper tag holder made out of 4 inches (10.1 cm) x 3 inches (7.6 cm) index cards. They fit an edge of about 1/4 (6.25 mm)
Read MoreHanging Buckets for Power Supplies
This kit of objects is two hanging buckets set for a cheap bench power supply. One bucket is 100 mm deep. The other is 50 mm deep. They are
Read MoreIkea Bror Caster Holder
This object lets you install casters to a Bror workbench. It is designed for 1-7/8″ (48.5 mm) x 2-9/16″ (65.5 mm) casters. The holes for the bolts are 2-1/8″
Read MoreIkea Ivar Vesa 100mm Mount
This is a 100 mm VESA mount designed to be mounted on the Ikea Ivar side units. As shown on the picture, I have used it to mount a
Read MoreIvar Side Unit Pin Hook
This is a small pin design to hang stuff on the vertical post of Ikea Ivar side units. The pin is 3mm in diameter, 10 mm long. Support is
Read More