Voltmeter Housing
This is a simple voltmeter housing. These voltmeters are widely available on AliExpress or eBay. Their display size is typically 2.4cm x 1.4 cm (0.36 inch). The mounting holes
Read MoreDecade Box Base Plate
This is a simple base plate for a popular Decade Box you can buy from China. The size of the Decade Box is 36mm x 90mm. You will need
Read MoreFLsun Cube Bed Adjustment Improvements
These are some improvements to the bed adjustment mechanism of the FLsun Cube. They provide: larger adjustment knobs protector for the heated bed protector for the aluminum bar. You
Read MoreFLsun Cube X Axis Motor Wire Guide
This is a simple X-Axis motor wire guide for the FLsun Cube. It is mounted using one of the screws of the linear bearing of the Y-Axis. You will
Read More2020 Extrusion Mosfet Holder
This is a Mosfet board holder that is made to be mounted on a 2020 extrusion. It has been specifically designed for a FLsun Cube. To mount it, you
Read More2020 Extrusion Spool Holder
This spool holder is designed to fit a 2020 aluminum extrusion. It is a replacement for the FLSun Cube spool holder. I recommend using 2 M5 x 10mm screws
Read MoreFLSun Cube Foot
This a part that is installed on the existing feet of the FLsun Cube. The stock feet made of aluminum damage the surface of the table on which the
Read MoreFLSun Cube Bowden Tube Strain Relief
This is a Bowden tube strain relief for the FLsun Cube. It should be installed near the extruder. You will need: 2 x M5x10mm bolts 2 x M5 hammer
Read MoreReprap Discount LCD Holder for 2020 extrusion
This Reprap Discount LCD holder has been specially designed for the FLSun Cube. This design lets you attach the display under a 2020 extrusion. You will need: 2 x
Read MoreFLSun Cube X-Axis Belt Tensioner
The FLSun Cube 3D printer does not come with an X-Axis belt tensioner. So, I designed one. The design is simple but very effective. It is mounted using the
Read MoreFLSun Cube Bed Level Adjustment Tool
This is a simple tool to adjust the level of the bed of a FLSun Cube. Likely, it can be used with other printers such as the CR-10. Print
Read MoreFLSun Cube Bed Cable Strain Relief
This is a strain relief for the heated bed cables of the FLSun Cube. A zip tie is used to fix it to the bed frame. I drilled a
Read MoreFLSun Cube Extruder Cable Strain Relief/Holder i2
This is a strain relief for the wires and the PTFE tube attached to the extruder of the FLSun Cube 3D printer. It is installed using the bolts of
Read More2020 Extrusion Power Supply Stabilizer
This is a simple stabilizer for a power supply designed to be attached to a 2020 aluminum extrusion. This stabilizer is designed for the FLSun Cube. You will need
Read MoreFLSun Cube Extruder Cable Strain Relief/Holder
This is a strain relief for the wires and the PTFE tube attached to the extruder of the FLSun Cube 3D printer. It is installed using the bolts of
Read More20 mm wide 135 Degrees T-Slot Angle Brackets
20 x 20 x 20 mm, 20 x 40 x 40 mm and 20 x 60 x 60 mm 135 degrees T-Slot brackets. For 90 degrees versions of these
Read MoreEditing Extra large 20×4 LCD Project Box
This is a project box for a large 20 x 4 LCD display. The LCD module dimensions are 146mm x 62.5mm x 20mm (5.75 inches x 2.46 inches x
Read MorePrusa i3 X-Axis Leveling Tool
This is a simple tool that will help you level the X-axis of a Prusa i3. You will need to print two of this. You can use them either
Read MoreJetson Nano Base with Camera
This is a simple base plate for the NVidia Jetson Nano development board along with a Raspberry PI v2.1 camera holder. It can be tilted and panned. To assemble
Read MoreEPM240 CPLD Development Board Base Plate
This is a base plate for the Altera Max II EPM240 CPLD Development Board from LC Technologies. You will need 4 M2 x 4mm screws to assemble it. No
Read More