Ivar Cable Hanger

  This is a cable hanger to be installed on the side unit of the Ivar shelving system. You will need 2 #4-40, 1/2″ bolts and the matching nuts. Support

Read More

Business Card Holder

  This is a simple business card holder that can be hang on a 5 mm wide support. It can hold about 50 cards. It should be printed upright with

Read More

Power Brick Holder

  This is a holder for a power brick of 18 cm (7 inches) in length, 4.5 cm (1 3/4 inch) tick and typically 7 cm (2 3/4 inches) in

Read More

P4.75-1R1G-16S Led Matrix Stand

  This is a set of feet for the p4.75-1R1G-16S Led Matrix (32 x 64). It holds the display at a 30-degrees angle. You will need two 8mm M3 screws

Read More

Recycling Bin Holder

  This is a Recycling Bin Holder 220 mm long. It is held by two screws. No support is needed. This object was designed using Fusion 360 Printable Files  

Read More

DFR-0499 Led Matrix Stand

  This is a set of feet for the DFR-0499 RGB Led Matrix (64 x 64). It holds the display at a 30-degrees angle. You will need two 8mm M3

Read More

Parametric Storage Box

  This is a simple SCAD file that generates a storage box and its cover. To create a box: Open the ParametricBox.scad file with openScad ( http://www.openscad.org/ ) Modify the

Read More

Foam Board Screen

  These are simple brackets used to build a screen from 5 mm foam board. Using the proper size of foam board, it can be used for airbrushing, etc. Print

Read More

Insulated Screwdriver Rack

  This is a compact rack for the Mastercraft Insulated Screwdrivers set (8 pieces) (#057-3695-4) No support is needed if printed on its side. This object was designed using Fusion

Read More

Insulated Precision Screwdriver Rack

  This is a compact rack for the Mastercraft Insulated Precision Screwdrivers set (6 pieces) (#057-3604-2) No support is needed if printed on its side. This object was designed using

Read More

Golden Airbrush Paint (30 mm) Caddy

  This is a caddy that can hold up to 18 Airbush Paint Bottles. The bottle can have a diameter of up to 30 mm. The design allows to print

Read More

Single Edge Razor Blade Rack

  This is a simple rack that holds 4 single edge razor blades. Support is not needed. This object was designed using Fusion 360 Printable Files    Single Edge Razor

Read More

Pro’s Kit Hex Nut Driver Rack

  This is a compact rack for the Pro’s Kit 7 Pcs Electronics Hex Nut Driver Set (#1PK-9402). If printed on its side, no support is needed. This object was

Read More

White Board Organizer

  This simple white board organizer can hold 10 markers along with the eraser. Support is not required. This object was designed using Fusion 360 Printable Files    White Board

Read More

Ender-3 Y-axis Endstop Holder

  The Y-Axis must be moved if a motor damper is installed. Otherwise, the carriage will hit the motor. The original Y-axis end stop holder is designed to use M4

Read More

Wera Electronics Screwdriver Rack

  This is a compact rack for the Wera 1578 A/6 Electronics Screwdriver Set. It takes less space the supplied one. If printed on the side, no support is needed.

Read More

Gocheer Airbrush Stand For Model 180

  This is a stand for the Gocheer airbrush model 180. Support is not required. 15% infill is enough. This object was designed using Fusion 360 Printable Files    Gocheer

Read More

Thermometer Mounting Brackets

  This is a mounting bracket for a small thermometer. You can buy it on AliExpress for about $1.00. I use it to monitor the temperature inside the enclosure of

Read More

3D Printing Tool Caddy

  Yes, another 3D Printing Tool Caddy! It contains only the essential tools. It can hold: Two glue sticks Twezzer Flush cutter X-Acto knife Flashlight Spatula No support is required.

Read More

FLsun QQ Enclosure

  The way the FLsun QQ is designed makes it easy to enclose it. Printing ABS is possible with this enclosure. The printer sides are covered with a five mm

Read More