Alligator Clip Cable Pegboard Holder (updated)

  It can hold up to 20 alligator clip cables. It is designed to be used with a North American pegboard. The distance between the holes is 1 inch (2.54

Read More

Parametric Open Box

  This is a simple SCAD file that generates simple open boxes without chamfers or fillets. They fit snuggly together. A sample is included. To create a custom one: Open

Read More

Ivar Side Unit Hook

  This is a simple Ivar Side Unit hook. No additional hardware is required. It can be printed without support. This object was designed using Fusion 360 Printable Files  

Read More

FLSun Cube Part Cooling Fan

  This is a part cooling fan for the FlSun. The original design has only one fan that cools the extruder and the part at the same time but it

Read More

Flsun Cube Nozzle Cooling Duct

  These objects replace the poor stock nozzle cooling system provided by FLsun. You will need 2 x M3-20 mm bolts and nuts to mount the fan along with the

Read More

Bearing containers of various sizes

These are various cylindrical containers. Each container holds 10 bearings. For each size, two parts are required: the base and the lid. There are containers for the following bearings: 603ZZ,

Read More

FLsun Cube Extruder Holder

  The stock Flsun Cube extruder is quite bad. I replaced it with an all-metal one available almost everywhere. The holder didn’t fit anymore. So I designed this one. Also

Read More

Wire Spools

  Wire spools of various sizes. The main picture is the 60 x 40 mm wire spool. It holds about 20 meters (10 meters of 2 conductors wire) of 26

Read More

Dremel Disk Protectors

  These tool add-ons protect the cutting disks while being in storage and still mounted on their shaft. Two sizes are supplied: 28 mm and 36 mm. No additional hardware

Read More

Voltmeter Housing

  This is a simple voltmeter housing. These voltmeters are widely available on AliExpress or eBay. Their display size is typically 2.4cm x 1.4 cm (0.36 inch). The mounting holes

Read More

Decade Box Base Plate

  This is a simple base plate for a popular Decade Box you can buy from China. The size of the Decade Box is 36mm x 90mm. You will need

Read More

FLsun Cube Bed Adjustment Improvements

  These are some improvements to the bed adjustment mechanism of the FLsun Cube. They provide: larger adjustment knobs protector for the heated bed protector for the aluminum bar. You

Read More

FLsun Cube X Axis Motor Wire Guide

  This is a simple X-Axis motor wire guide for the FLsun Cube. It is mounted using one of the screws of the linear bearing of the Y-Axis. You will

Read More

2020 Extrusion Mosfet Holder

  This is a Mosfet board holder that is made to be mounted on a 2020 extrusion. It has been specifically designed for a FLsun Cube. To mount it, you

Read More

2020 Extrusion Spool Holder

This spool holder is designed to fit a 2020 aluminum extrusion. It is a replacement for the FLSun Cube spool holder. I recommend using 2 M5 x 10mm screws with

Read More

FLSun Cube Foot

  This a part that is installed on the existing feet of the FLsun Cube. The stock feet made of aluminum damage the surface of the table on which the

Read More

FLSun Cube Bowden Tube Strain Relief

  This is a Bowden tube strain relief for the FLsun Cube. It should be installed near the extruder. You will need: 2 x M5x10mm bolts 2 x M5 hammer

Read More

Reprap Discount LCD Holder for 2020 extrusion

  This Reprap Discount LCD holder has been specially designed for the FLSun Cube. This design lets you attach the display under a 2020 extrusion. You will need: 2 x

Read More

FLSun Cube X-Axis Belt Tensioner

  The FLSun Cube 3D printer does not come with an X-Axis belt tensioner. So, I designed one. The design is simple but very effective. It is mounted using the

Read More

FLSun Cube Bed Level Adjustment Tool

  This is a simple tool to adjust the level of the bed of a FLSun Cube. Likely, it can be used with other printers such as the CR-10. Print

Read More