Category: object
EPM240 CPLD Development Board Base Plate
This is a base plate for the Altera Max II EPM240 CPLD Development Board from LC Technologies. You will need 4 M2 x 4mm screws to assemble it. No
Read MoreJetson Nano Base Plate
This is a simple base plate for the NVidia Jetson Nano development board. 4 x #4-40, 1/4″ bolts are required to assemble it. No support is required. An infill
Read MoreParametric Bottle Rack
This is a simple SCAD file that generates bottle rack. Various sizes are included. To create a custom one: Open the ParametricBottleRack.scad file with openScad ( http://www.openscad.org/ ) Modify
Read MoreParametric Drink Coaster
This is a simple SCAD file that generates round coaster. Various sizes are included. To create a custom one: Open the ParametricCoaster.scad file with openScad ( http://www.openscad.org/ ) Modify
Read MoreIvar Cable Hanger
This is a cable hanger to be installed on the side unit of the Ivar shelving system. You will need 2 #4-40, 1/2″ bolts and the matching nuts. Support
Read MoreBusiness Card Holder
This is a simple business card holder that can be hang on a 5 mm wide support. It can hold about 50 cards. It should be printed upright with
Read MorePower Brick Holder
This is a holder for a power brick of 18 cm (7 inches) in length, 4.5 cm (1 3/4 inch) tick and typically 7 cm (2 3/4 inches) in
Read MoreP4.75-1R1G-16S Led Matrix Stand
This is a set of feet for the p4.75-1R1G-16S Led Matrix (32 x 64). It holds the display at a 30-degrees angle. You will need two 8mm M3 screws
Read MoreRecycling Bin Holder
This is a Recycling Bin Holder 220 mm long. It is held by two screws. No support is needed. This object was designed using Fusion 360 Printable Files
Read MoreDFR-0499 Led Matrix Stand
This is a set of feet for the DFR-0499 RGB Led Matrix (64 x 64). It holds the display at a 30-degrees angle. You will need two 8mm M3
Read MoreParametric Storage Box
This is a simple SCAD file that generates a storage box and its cover. To create a box: Open the ParametricBox.scad file with openScad ( http://www.openscad.org/ ) Modify the
Read MoreFoam Board Screen
These are simple brackets used to build a screen from 5 mm foam board. Using the proper size of foam board, it can be used for airbrushing, etc. Print
Read MoreInsulated Screwdriver Rack
This is a compact rack for the Mastercraft Insulated Screwdrivers set (8 pieces) (#057-3695-4) No support is needed if printed on its side. This object was designed using Fusion
Read MoreInsulated Precision Screwdriver Rack
This is a compact rack for the Mastercraft Insulated Precision Screwdrivers set (6 pieces) (#057-3604-2) No support is needed if printed on its side. This object was designed using
Read MoreGolden Airbrush Paint (30 mm) Caddy
This is a caddy that can hold up to 18 Airbush Paint Bottles. The bottle can have a diameter of up to 30 mm. The design allows to print
Read MoreSingle Edge Razor Blade Rack
This is a simple rack that holds 4 single edge razor blades. Support is not needed. This object was designed using Fusion 360 Printable Files Single Edge Razor
Read MorePro’s Kit Hex Nut Driver Rack
This is a compact rack for the Pro’s Kit 7 Pcs Electronics Hex Nut Driver Set (#1PK-9402). If printed on its side, no support is needed. This object was
Read MoreWhite Board Organizer
This simple white board organizer can hold 10 markers along with the eraser. Support is not required. This object was designed using Fusion 360 Printable Files White Board
Read MoreEnder-3 Y-axis Endstop Holder
The Y-Axis must be moved if a motor damper is installed. Otherwise, the carriage will hit the motor. The original Y-axis end stop holder is designed to use M4
Read MoreWera Electronics Screwdriver Rack
This is a compact rack for the Wera 1578 A/6 Electronics Screwdriver Set. It takes less space the supplied one. If printed on the side, no support is needed.
Read More