Mount a partition from a full disk image file on Linux

This post explains how to mount a partition from a disk image file on a Linux system. Such a file may have been created using the dd command. The disk

Read More

Linux whole data disk encryption

This post give the main steps to achieve full data disk encryption. The disk password will be required during boot time. You will need the device name of the disk

Read More

How to create an encrypted file and open it

You’ll find in this post the basic steps to create an encrypted luks file and open it. You’ll need to perform the following steps to create it: The following steps

Read More

Parametric Clickable Stamps Holder

Parametric Clickable Stamp Holder. It fit out of the box, the stamps distributed by Michaels’. The item numbers of these stamps are 10656553 and 10656558. Holder for 3 to 9

Read More

Ikea Ivar Caliper and Folding Ruler holder

This is a holder for a Caliper and Folding Ruler for the Ikea Ivar. It is designed for the side units. The width of the folding ruler is 1.6 cm.

Read More

Parametric Clickable Stamp Case

This is a parametric clickable stamps case. It fit out of the box the stamps distributed by Michaels’. The item numbers of these stamps are 10656553 and 10656558. Support material

Read More

Triple 5mA battery trickle charger

Triple 5mA battery trickle charger ——————————————————————————– This is a 5mA lead acid battery trickle charger along with its case. It works with any battery up to 35V. You can maintain

Read More

Pen Holder V05

This is another variation of the pen holder published previously. This one is the largest. It can hold about 64 pens. The top part of it is modular. It can

Read More

Parametric Container with an overlapped lid

This is a parametric container with an overlapped lid. Support material is not required. An infill of 20% is recommended. This object was designed using openSCAD. Printable Files    Example

Read More

8 ml Inkwell

This is a small 8 ml inkwell design to be used to refill a fountain pen. Test it with water before putting ink in it. Printing parameters may prevent it

Read More

Parametric Stamp Handle

This is a parametric stamp handle. It works pretty well with silicon stamps. I’ve used superglue to attach the stamp to the handle. A sample STL file is provided. Use

Read More

Simple human interface for Home Assistant

This is a simple human interface project for Home Assistant. It helps me remind doing 2 daily tasks. Using Home Assistant automation, it lit a LED at a given time

Read More

Manna Water Bottle Stand

This is a stand used to dry a Manna water bottle. Support material is not required. An infill of 30% is recommended. This object was designed using Solid Edge Community

Read More

Foldable To-do List Manager

This is a stand for managing to-do lists based on 1/8 of a letter size sheet of paper or 3″ x 5″ index cards. Templates are included for you to

Read More

One Eight Letter Size Page To-do List

This is a stand for managing to-do lists based on 1/8 of a letter size sheet of paper. A template is included for you to draw your to-do lists. It

Read More

Half Index Card To-do List

This is a stand for managing to-do lists based on half 3″ x 5″ index cards. A template is included for you to draw your to-do lists. It can be

Read More

Parametric Box With Flush Cover

This is a parametric box generator with a cover flush with its body. Support material is not required. An infill of 20% is recommended. This object was designed using OpenSCAD.

Read More

Parametric Bearing Container

This is a parametric bearing container generator. Some bearing definitions are supplied. It is easy to add some. Support material is not required. An infill of 20% is recommended. This

Read More

Parametric Cylindrical Objects Container with Lid

This is a parametric cylindrical objects container with lid generator. This object was primarily design to hold a set of round magnets. Support material is not required. An infill of

Read More